Pages

Showing posts with label HAD Oy. Show all posts
Showing posts with label HAD Oy. Show all posts

Thursday, 14 February 2013

Speaker "pillows"

I apologize once again for the low activity the last few weeks. Lots of stuff going on at school, lots of work at the new job and I just started getting my driving license as well. But a week ago or so I got a package from Ingvar which contained some speaker "pillows". Not the famous SD-pillows I have mentioned before because he said the speaker became too unstable on them. So instead he sent me some thinner pillows of a similar material. They made a huge difference, mostly in the midrange. Now the floor vibrates a lot less and the sound is generally cleaner.


It has been squished a bit by the weight of the speaker


Monday, 4 February 2013

You know you have been playing loud when...

So I was fooling around a bit this evening playing some dubstep. I measured an average level of about 102dB and peak at 106dB in the bass frequencies.


Note the port cover. It is made of some kind of mesh material and it allows air to pass quite freely. Breathing through it is no problem at all, you barely notice any extra resistance. It's the same on both speakers.

Picture quality is bad, I know. But I have no functioning memory card for my camera yet but hopefully two 8GB cards arrive either tomorrow or on wednesday. I have also ordered a 3TB Western Digital Red harddrive to store all my music, pictures and movies on. Feels like it was a good investment, especially since my WD Black 640GB has almost 12000 hours uptime, who knows when it fails?

Sunday, 3 February 2013

First try at room measuring


Here's some different measurements I did a while ago using an Audyssey mic and an integrated soundcard on my motherboard. No scientific standards but...

The two highest curves are with no damping in the ports, the two lower are with damping. The lowest two with and without damping is with door to the room open and the highest is with door closed.

The room gives the big peak around 50Hz and the suckout between 80-100Hz. I don't know about 200Hz yet but I suppose that's some other feature of the room's dimensions.

Tuesday, 15 January 2013

"New" speakers again!

No, I'm not selling my Oy speakers and building something else. It just feels like I have new speakers again.

I'll start the story from beginning, instead of starting in the middle, going towards the end and then finishing with the beginning as I did on diyaudio.com earlier today.

I have always had a feeling there's something wrong with the speakers. Very bass-shy and diffuse soundstage. And on the first days when I was turning the speakers against eachother with a ~2cm gap in between and connecting them out of phase I still had a decent output when playing 20Hz sine waves. Not loud, but it was enough to disturb people around the house. But I didn't care more about that. I was just thinking they were bass-shy because they needed more burn in time.

Back to present time. While cleaning my room last friday I found a bag with sealing gaskets. They were supposed to be around the driver and terminal cutouts. So today I had some spare time so I assembled a table to work on and I opened up speaker number one, the one with the damaged baffle. Everything was fine, all cables connected as they should be. But on speaker number two I found the problem. The upper woofer was wired out of phase. Apparently I was in such a hurry to get them up and running so I didn't have time to double check the polarity. So I added the sealing gaskets, mounted the drivers and double-checked the polarity and WOW what a difference!

In theory I should have twice as much bass now than before, and boy I do! I can feel it easily in my chest even at lower volumes. Before I had been playing them without any damping material in the ports, but now I put in all of it and I'm almost thinking of adding some more to further attenuate the bass.

Another thing is the soundstage which got improved a lot. Now it's possible to hear where the musicians are on the stage and it's just wider, deeper and larger in general.

And here's some pictures of the sealing gaskets






Friday, 4 January 2013

Trying the speakers in the living room


Trying the speakers in the living room during the LAN-party. Sounds good so far, and it's getting better for every hour.

Thursday, 3 January 2013

After several hours of sanding I'm finally done!

I'm finally done with the HAD Oy speakers!

No pictures in this post, that will come later. Neither will I make any comments about the sound because I want to give them at least 100 hours before commenting the sound. But I can say that they can play loud, louder than my ears can handle, and that I'm not used to listening to speakers that have tweeters ;)

Tuesday, 1 January 2013

Almost "done"!

This will be a quite short post, mostly just facts so I can remember what I've done when it is time to write my report for school. Quite tired after a long day, you see.

I started with screwin the filter to speaker number one.


Then I added damping material to the side for speaker number one, and cutting away some for the braces.
I also added some hot glue to the bolts on the filters, just to keep them in place.


Added some clamps to hold the cable in place.


Speaker number one is being glued. Didn't need very many clamps for this, the weights were enough. The garden stones weight 14kg each. I have also dampened the second side panel. The brace is higher up in the box in speaker number two, as you can see in the cutouts in the damping material. It accidentally became like that, and I noticed it first after I had glued them so I couldn't be arsed to fix it.


When speaker number one had gotten some hours to dry I carried it to the garage and spent about 1½ hour sanding it. First a run with 40's paper to do most of the work at some places. Then a run with 120's over all panels and joints. I also spent 10-15 minutes carving away glue. Thick pieces of glue can't be sanded really, has to be cut away.

Then I carried them back in again and it was time to mount the terminals. Problem!
The spade connectors were too small. There was too little metal to drill the holes larger so I had to cut them off and replace them with bigger ones. Luckily I had a few centimeter more cable than I needed.


Small vs big one
With the new ring connectors I mounted them to the terminal. Problem again, see the picture. I was just about to go ask dad for help and advice but I came up with a solution myself. Why shall the cable point down when the filter is above the terminal? Loosen the bolt, rotate the connectors 180 degrees and it's fine. Four screws later the terminal was fixed in place.



Up and running!
It was quite funny though. Mom, dad and my brother had been saying "What if it's dead quiet when you turn it on for the first time" and I've been saying that it wont. Guess what happened, it was dead quiet. The Mar-Kel speaker on the right channel was playing fine though. Checking the speaker cables twice, everything is fine. Decided to connect the left Mar-Kel again and see if it works. No it didn't. I check my Reckhorn active filter and a cables has come off. Probably because me and dad were lifting the amplifiers earlier today when we needed the garden plates. Put the cable back in and everything was fine.

I wont comment about the sound yet, I'll play them for a couple of days before I will write about the sound. All speakers sound like shit when the drivers come straight from the box never being played, so I'll try to play them as much as possible in the coming week and wait for them to loosen up a bit.

Monday, 31 December 2012

Happy new year, and glueing!


Right now I'm glueing braces in both speakers. Both speakers are almost done with the damping material, the left one has a bit left by the port and the baffle. I will do the tomorrow when the braces have dried.

Then I will carry #2 outside for drilling and sanding. Then I will screw in the filters and hope that the back panel fits without problems. If it does I will glue both sides tomorrow and have them up and running in the evening or on wednesday.

The smell of burnt rubber...

I've been working about as much today as I did yesterday, maybe even more time-wise.

First thing I did in the morning was to glue the baffle.

Then I went outdoors to the garage and started with the damping materials. I didn't take any pictures since my father and brother were out there sanding some stuff so it was a bit dusty. But I cut all the pieces for speaker number one and fastened most of it. For speaker number two I still have to cut the pieces that shall be on top of the port pieces.

When I was done with the damping material the baffle had gotten a few hours to dry so I started glueing the bottom.

Then it was time to solder the filters, which proved to be a bit harder than I thought.

Using my own equipment this time and not Daniel's

I started with stripping and tinning the cables, thinking it was a great idea. It was great, until it was time to solder them to the filter. I managed to get two of the - cables on before I realised that it wasn't possible. The big 4mm cables were too thick to be soldered easily. So then dad came up with the idea that I could use cable shoe rings and a bolt instead and just solder the bolt to the filter, and so I did. But now the cables were all tinned to getting the cables shoes on the cables was a bit hard and I had to solder them as well. I guess I spent probably two hours or so soldering the filters.




When I was done with the filters the bottom panel had gotten a few hours to dry so it was time to glue the port.


I used less glue this time so aligning it right was much easier than before.

And some time during the day, can't remember when exactly, I tried mounting all the drivers in speaker number one to assure that all t-nuts were straight enough and most of them were. The ones that needed to be fixed got fixed. It was then I realised I had forgotten to drill the holes in the tweeters. Me and dad went out to the workshop, dried some different drills and found that 4.5mm would be fine. Drilled all six holes and I was really nervous but dad showed no signs even though he was drilling.

Holes are now ~4.5mm instead of ~3.5mm so now the M4 bolts fit through
And for those of you wondering about the title of this post, my mom complained several times that it smelled of burnt rubber in the house. It's because I had used lots of head when soldering so the insulation on the cables had melted a bit at some places. "Luckily" I have anosmia and can't feel the smell at all so I wasn't bothered by it.

Sunday, 30 December 2012

Last update for this very productive day

I have done a lot of stuff since this morning. The first thing I did was to use a very sharp carpet knife to carefully cut loose the birchply piece from the oak spacer bit.

I will try to glue it back and then fill with some bondo or something, sand it down and see how it looks like. If it's not good I might try an inlay. If that isn't good either I might just paint the boxes.

While I was in the little workshop I pre-drilled holes in the port pieces and glued and screwed them together like this.

I also drilled holes in the filters to prepare for screwing them to the back panel. I want the filters removable so I wont glue them.


I noticed that the big condensators were a bit loose and could rattle so I used some superglue and glued them to the boards like this.



Then before going to the gym I glued the bottom panel for speaker number one.


When I came home from the gym I started again with glueing the back panel of speaker number two.


And while I was waiting for dinner I made cables from the terminal to filter and then from filter to upper woofer, to both speakers.


I have not stripped the inner insulation from the other ends yet. I will do that when I am soldering them to the filter (maybe tomorrow or on wednesday).

Then I carried speaker number one outdoors into the garage. Found a nice workbench of suitable height there to place the speaker on. There I sanded the edges on the side where glue had come up, so the side panel fits nicely when it is time to glue it. I also drilled holes for the terminal plate screws and for the filter screws.



And a couple of hours ago I started glueing the top panel for speaker number two. I will let this be for the night and then glue baffle and bottom panel early in the day. In the evening I will glue ports for both speakers and start with the damping material.



Update!
I wasn't done for today it seemed. Dad thought I should glue the port for speaker number one and so I did.


It was a bit tricky to make it stay in place but after a while I got it to 50mm +- 1mm which shouldn't matter very much I think since I will stuff the port anyways.

Tomorrow the main goal is to glue baffle and bottom to speaker number two. Then add damping material to all panels that shall have it. Cut out for braces and filter and glue the braces. Then drill holes for terminal plate screws for speaker number two, sand joints and drill holes for filter screws.

After that, all that remains is solder all the cables to the filter, mount the filter and then glue the remaining side panel (hoping that it fits because I know not all angles are 90 degrees).

A minor disaster!

So this morning, I was still in bed, my dad started to remove the clamps from the speakers. Some of the spacer bits we've used to avoid damaging the panels had gotten stuck. Apparently some glue had found its way between spacer and baffle and so the spacer had been effectively glued to the baffle. Glue is very strong so he used a hammer to knock it off. This particular bit was of oak and as you all know oak is very hard, harder than birchply, so the birchply gave way and it ended up like this.







A big disappointment of course. It's on the baffle, close to the edge (which could be both good or bad) and far down (which is also good and bad).

But I decided to try to remove the bit that had stuck to the oak. I used a very sharp carpet knife and carefully cut it off. Starting in one end going towards the middle and then turning it around and starting at the other end and going towards the middle.


So I guess I will make an attempt to glue it back into the hole and then use some bondo or something and see how it ends up like.

Day two of glueing the Oy

Today I continued glueing the speakers. I started with glueing the top panel.

Lots of speaker cabinets in one picture!

Somehow the top panel is ~1mm too thick at some places. No biggie since I am thinking of chamfering  all edges like Ingvar has done.
For this it was easier to have the speaker standing, so I could add weights on top. I still have the whole box "assembled" except for the side panel to make it easier getting all the angles correct. This has one drawback though, because the glue also has contact with the panels that are not being glued at the moment. So when I was going to glue the baffle today some glue from the top panel had gone to the baffle so I had to use a hammer to get the baffle loose. This lead to some wood splintering on the inside of the baffles, no big deal though since it wont be visible anyways.

And in the evening when the glue has gotten some hours to dry it was time to glue the baffles.

Using all available clamps but I could still use a few more. Might be I'll raid my neighbour's garage and see if he has any. The glueing of the baffle went smoother than the back panel because I can put clamps in the driver cutouts as well.

Tomorrow I will not spend the whole day in front of the computer playing Dota 2 as I have done today. Tomorrow I will glue the bottom panel early in the morning. Then I will screw and glue the two port pieces together, for both speakers. I will mark and maybe drill holes for the terminal backplate. I will pre-drill holes in the filter boards and backside of the speaker so I can screw the filter boards instead of glueing. I want to be able to remove them if needed so glueing is not an option. Then I will make a new pair of cables for the top woofer and then a pair of cables from terminals to filter and put a ring connector on the terminal end. If I have time I will also solder all cables to the filters. A lot of work, and it will take many many hours but hopefully I shall have time to go to the gym at some time during the day.

Saturday, 29 December 2012

Glueing the very first piece of the Oy speakers

Today it was time to start on the Oy speakers, for real. I started with clearing my working table and then getting all the needed parts for one speaker and quickly taping it up to see how everything would fit. After a couple of minutes of discussing with dad what would be the best way to glue them we start working. Get clamps, all the clamps we have, and place the speaker on three of them. Add glue, a little of pressure from the sides and then adjust the back panel sidewise  before adding the weights on top. I used the old baffles for the Mar-Kel70 speakers to put the weights on. In the end it looked like this.




I pretty much used all the heavy objects I could possibly find. At first I put the weights on the sides but there was a little gap in the middle so I decided to move it all to there instead.




As you can see in the first and last pictures the gap is by the middle clamp, and it's quite small, about a millimeter or less. On the sides it's all fine, as you can see in the middle picture. I guess I will just add some more glue later and then sand it down, just to fill the hole. It is 100% sealed though, because the glue filled up nicely all the way on the inside. And if I want I could seal the entire cabinet from the inside later if I want to, but I guess there will be no need for that.